![]() WX/TERR PUSHBUTTON (momentary action) - shows or turns off the display of the radar or Enhanced GPWS (EGPWS) symbology on the MFD NAV page if ARC is selected and Weather/Radar and/or EGPWS are active PUSH - removes the weather radar and EGPWS images (but WX/TERR operating mode is still displayed) PUSH 2 - displays EGPWS terrain information PUSH 3 - displays weather radar information (default selection) Ħ 4 5 FMS AUX ADF VOR OFF TCAS WX TERR DATA VOR2 ADF2 FMS2 OFF AUX2 BRG PFD FORMAT MFD BRG WX/TERR BRT BRT RANGE OFF OFF MIN 7 6 Figure EFIS Control Panel (EFCP) (2 of 2) ħ EFCP CALLOUTS PERTAINING TO NAVIGATION ITEMS (cont d) 4. Note: If the EFCP malfunctions, the TCAS automatic mode is set. ![]() TCAS PUSHBUTTON (momentary action) PUSH - shows TCAS traffic continuously when navigation page is set to arc or map Mode and range is set to 40 nautical miles or less, - TCAS range ring indication comes inte view to show continuous indication selection. Optional navigation data may be displayed in that mode, using the DATA pushbutton, but not the weather radar image 3. This partial compass mode displays ± 45 around the current heading PUSH and HOLD ( sec.) - the NAV display on MFD changes to a FULL mode, A/C centered, oriented with respect to north. FORMAT PUSHBUTTON (momentary action, second hold) PUSH - ARC mode with VOL/ILS as navigation source PUSH 2/3 - the NAV display on MFD changes back to ARC mode with FMS (default selection) as navigation source. selected, and the FMS is operating, the pointer will point to the next waypoint - AUX is only functional with optional equipment, i.e., MLS 2. BEARING SELECTOR knob (5 position, rotary action) ROTATE - selects desired navigation source to be displayed by the white, single bar bearing pointer with a white circle, on the PFD - selectable positions are labeled OFF, VOR, ADF, FMS and AUX - bearing pointer is removed from PFD display when turned OFF - selected navigation source is annunciated on the PFD - If VOR is selected, but the frequency is either invalid, or an ILS frequency, the pointer will be removed from view - If ADF is selected, but the signal of frequency is invalid, the pointer will park at the 90 position - If FMS i.e. ĥ EFCP CALLOUTS PERTAINING TO NAVIGATION ITEMS. However, the intensity may appear degraded with certain types of sunglasses such as dark and/or polarized lenses. ![]() MFD 2 REVISION SELECTOR (rotary action, 4 position) TURN - selectable positions are ENG, NAV, SYS, PFD - ESCP provides the copilot with the ability to select any page on the MFD2 and to control the EIS reversion after display failures - the MFD2 selector switch is usually set to the SYS position when the copilot is the PNF, and to NAV when PF Ĥ Figure EFIS Control Panel (EFCP) ( of 2) NOTE: DISPLAY INTENSITY (PFD, MPD, BRT Knobs) Display intensity has been fully evaluated and is adequate in all lighting conditions including bright sunlight. MFD REVISION SELECTOR (rotary action, 4 position) TURN - selectable positions are PFD, NAV, SYS, ENG - ESCP provides the pilot with the ability to select any page on the MFD and to control the EIS reversion after display failures - the MFD selector switch is usually set to the NAV position when the pilot is the PF, and to SYS when PNF 2. ![]() Introduction The Dash 8-Q400 has standard navigational equipment allowing it to be fully certified for VFR and IFR navigation General Navigation equipment includes: Very High Frequency Omni Range (VOR) Instrument Landing System (ILS) Marker-Beacon Distance Measuring Equipment (DME) Automatic Direction Finder (ADF) Transponder Weather Radar Flight Management System (FMS) PageĢ 2.5.3 Controls and Indications - Navigation ģ 2 PFD NAV SYS ENG ELEC SYS ENG SYS FUEL SYS NAV SYS PFD ENG MFD DOORS SYS ALL TEST MFD2 NORM 2 EFIS ATT/HDG SOURCE OFF ED BRT NORM 2 EFIS ADC SOURCE Figure 2.5- Engine and System Integrated Display Control Panel (ESCP) ESCP Callouts pertaining to navigation items.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |